Wall Panelling Kits: Plan Shaker Grids and Decorative Frames

Wall panelling looks most convincing when the layout belongs to the room. The width of a panel, the spaces between frames and the way the pattern meets a door can matter more than the amount of moulding used. This guide explains how to compare Shaker-style strips, decorative panel frames and individual mouldings, then plan a layout and order that make sense for your walls.


By JJ Building Materials
8 min read

Richard Burbidge 1pk PaintReady Wall Panel Kit 1000x75x75mm

Wall panelling looks most convincing when the layout belongs to the room. The width of a panel, the spaces between frames and the way the pattern meets a door can matter more than the amount of moulding used. This guide explains how to compare Shaker-style strips, decorative panel frames and individual mouldings, then plan a layout and order that make sense for your walls.

Choose the type of panelled effect first

There are several ways to create a panelled appearance. Applied flat strips can form a Shaker-style grid, while decorative mouldings can frame areas of the existing wall. Tongue-and-groove or other cladding creates another type of surface altogether. Decide which effect you want before comparing prices, because a kit of strips and a kit of shaped frame pieces are not necessarily equivalent products.

The JJ Building Materials mouldings collection includes PaintReady kits and separate profiles for different approaches. Read the contents and dimensions of the selected product rather than assuming that every item called a wall panel kit covers a fixed square-metre area. The finished coverage depends on the kit design and, in some cases, the spacing you choose between components. Ask for the fitting guide when that relationship is unclear.

Shaker-style strips suit a planned grid

The Richard Burbidge PaintReady 60 × 1200 × 9mm Shaker kit and 60 × 2400 × 9mm Shaker kit provide different strip lengths to investigate for your layout. Longer pieces can be useful where a continuous run is required, but they do not eliminate the need for a cutting plan. Check the number of strips supplied and which dimensions describe each piece.

Strip width changes the balance between the framework and the spaces within it. A relatively broad strip creates a stronger grid, while a narrower one leaves more visible wall within the same overall area. Do not choose the width independently of the panel spacing. Draw one complete bay at full scale with removable tape and look at it from the doorway as well as close up.

Richard Burbidge 1pk 6 PaintReady Shaker Kit 60x1200x9mm
Richard Burbidge 1pk 6 PaintReady Shaker Kit 60x1200x9mm — check the selected variant for dimensions, finish and supplied components.

Decorative frames create a different kind of detail

Framed panels use shaped mouldings to create outlined areas on the wall, with the wall itself often remaining visible inside. Compare the Richard Burbidge PaintReady 700mm wall panel kit with the 420mm wall panel kit, checking the manufacturer's layout information and the listing's contents. The product name alone should not be used to infer the assembled external size or the exact area covered.

Frame profiles create shadows that change with the room's lighting. A shallow, simple section can feel restrained, while a more detailed profile adds a stronger decorative line. Consider the existing skirting, architraves and cornice before adding another style. You do not need every profile to be identical, but the new detail should look intentional beside the joinery that is staying.

Decide whether a dado is part of the design

A half-height treatment can end with a rail, while full-height frames may use a different arrangement. The Richard Burbidge PaintReady wall panel kit with dado is worth comparing where a top rail is part of your plan. Confirm what is supplied and how the sections relate to the frames before calculating quantities. A kit with a rail should not be priced against one without it as though their contents were the same.

There is no single correct dado height for every room. Test the proposed line against window sills, sockets, furniture backs and existing features. A height that looks balanced on one wall may create an awkward junction on another. Mark a continuous line around the room and inspect the transitions before committing. The aim is a coherent layout that responds to the actual space, not a measurement copied without context.

Survey the wall as it exists

Measure each wall separately and mark doors, windows, sockets, switches, radiators and fixed furniture. Record their positions from consistent reference points. Check whether the wall is sound, dry and suitable for the intended fixing method. Decorative mouldings should not be used to conceal an unresolved moisture problem, loose finish or damaged background that will undermine the installation.

Look at the room from normal viewing positions. A bed, sofa or cabinet may hide a large part of the pattern, and a radiator can interrupt a carefully drawn panel. Decide whether the design should continue behind removable furniture or end around fixed features. This affects both quantities and the appearance of the room if its furnishings change later. Do not plan solely from an empty-wall photograph.

Calculate equal panel spaces from a fixed overall width

For a simple flat-strip arrangement, begin with the usable wall width and decide how many open panels you want. Subtract the combined width of the vertical strips, including any end strips included in your design. Divide the remaining width by the number of open panels. This gives an initial spacing to test, not a substitute for checking the room and the chosen kit instructions.

As a planning example, a 3,000mm usable width with four 60mm vertical strips leaves 2,760mm for three openings, or 920mm per opening. That assumes the two end strips sit within the measured width and the three bays are equal. Changing the number or width of strips changes the result. Mark the arrangement on the wall and check obstacles before using it as a cutting specification.

Avoid forcing symmetry across every obstacle

Equal spacing can look calm, but a room may need a local adjustment around a doorway or a short return. Decide where symmetry matters most, such as either side of a central feature, and where a narrower bay is acceptable. A small wall beside a door does not necessarily need to repeat the full-width panels used on the main wall. What matters is a consistent design logic.

Try several layouts on paper before cutting. Move a panel boundary away from a socket where practical, and avoid leaving a tiny fragment beside an architrave. If electrical fittings need alteration, include appropriate professional work in the project rather than cutting around them without a plan. The panelling should respect access and operation of existing services, not make them difficult to use or maintain.

Richard Burbidge 1pk PaintReady Wall Panel Kit 700x75x75mm
Richard Burbidge 1pk PaintReady Wall Panel Kit 700x75x75mm — check the selected variant for dimensions, finish and supplied components.

Individual mouldings offer flexibility for unusual spaces

The Richard Burbidge primed panel mouldings provide another route when standard kit proportions do not suit the room. Individual lengths let you plan custom frames, subject to the selected profile and your cutting ability. Compare the cost and work involved with a kit, including measuring, cutting, finishing joints and using the remaining lengths efficiently. Flexibility is useful, but it comes with more setting-out decisions.

Check the actual section size when matching an existing decorative scheme. Two profiles described as panel moulding can differ in depth, curves and the shape of the back. If you are extending old work, use a sample or an accurate section drawing. Paint can soften small visual differences, but it will not make noticeably different profiles line up at a junction.

Plan the joints and ends before buying

Decide how horizontal and vertical pieces meet, and follow the chosen system's instructions. Some layouts use square joints while decorative frames commonly involve angled corners. Record whether a dimension refers to the outside edge, inside opening or a centre line. Confusing these measurements can produce a set of individually accurate cuts that do not form the intended frame when assembled.

Where the design finishes against an architrave or skirting, compare thicknesses. A strip projecting beyond adjacent trim may need a deliberate end detail. Do not discover this only after fixing the first wall. Build or draw a small sample junction and check it from the side. This is especially useful where a shallow moulding meets a substantial existing door surround or where two finishes will meet.

Order from the cutting list and kit contents

Write down every required piece, its finished length and any angled ends. Allocate those pieces to the stock lengths or supplied kit components, allowing for the saw cut and trimming. Then calculate packs. A kit containing six strips is not the same as six complete framed panels, and the same quantity of timber can produce different coverage depending on your layout.

Keep an allowance that reflects the actual complexity of the project rather than using a universal percentage without thought. A straightforward grid may use offcuts efficiently; several short walls with decorative corners may not. If you are new to cutting the chosen profile, allow material for test cuts. Confirm all quantities before installation so you do not have to interrupt the pattern while waiting for another pack.

Richard Burbidge Primed Panel Mouldings 2400mm
Richard Burbidge Primed Panel Mouldings 2400mm — check the selected variant for dimensions, finish and supplied components.

Primed does not mean the whole decorating process is finished

PaintReady and primed products reduce some preparation work, but the installed result still needs the appropriate finishing steps. Follow the product and paint-system guidance for handling cut ends, joints, fixing marks and final coats. Check compatibility rather than assuming that any paint can be applied in any conditions. Test your colour on a sample to see how it behaves over the supplied surface.

Consider the wall within the panels as part of the finish. If it remains exposed, its texture and condition will still be visible after the mouldings are fitted. Strong side lighting can emphasise uneven areas. Prepare that background to the standard you want before the decorative grid makes access more awkward, and plan the order of painting around the fitting and coating instructions.

Frequently asked questions about wall panel kits

Is a Shaker kit the same as a decorative frame kit?

No. Shaker-style kits commonly use flat strips to form a grid, while decorative frame kits use shaped mouldings for outlined panels. Read the contents and fitting guide for the selected product. Compare the finished design and work required, rather than treating every kit as the same amount of ready-made wall coverage.

How many panels should I put on a wall?

Start with the usable width, chosen strip or frame size and fixed obstacles. Test several layouts and judge the proportions from normal viewing positions. Equal spacing can work well, but the room may need adjustments around doors, windows or services. There is no single panel count suitable for every wall.

Can I use kits in a bathroom?

Check the exact product's permitted environment, background requirements and finishing instructions. Do not infer wet-area suitability from a painted appearance. Moisture exposure varies considerably within a bathroom, so the location and complete finishing system need to be considered before selecting decorative timber components.

Should I fit the panels over an uneven wall?

Assess and prepare the background first. Applied mouldings do not make loose, damp or badly uneven surfaces sound. A small variation may be manageable within the specified fixing method, but a significant defect needs an appropriate repair. Test the layout against the real wall before ordering all the material.

Do I need extra material beyond the exact measured length?

Usually the order must account for cutting losses, trimming and the way pieces fit within stock lengths or kits. Use a cutting list to calculate it. Allowing for test cuts and the complexity of the design is more reliable than assuming every offcut can be reused in a visible position.