Deck-Mounted Bath Fillers: Holes, Projection and Fitting Checks
Choosing a deck-mounted bath filler starts with the bath rather than the finish of the tap. The rim must accommodate the mounting arrangement, the spout must deliver water inside the bath and the connections need practical access underneath. A replacement that looks similar from above can have different centres, fixing dimensions or reach. This guide explains the checks that make it easier to choose a suitable bath filler for a new installation or a bathroom refurbishment.
Choosing a deck-mounted bath filler starts with the bath rather than the finish of the tap. The rim must accommodate the mounting arrangement, the spout must deliver water inside the bath and the connections need practical access underneath. A replacement that looks similar from above can have different centres, fixing dimensions or reach. This guide explains the checks that make it easier to choose a suitable bath filler for a new installation or a bathroom refurbishment.
Identify the bath and its permitted tap positions
Find the bath manufacturer's instructions and confirm whether the rim is supplied drilled, undrilled or prepared for particular fittings. An undrilled rim is not permission to drill anywhere. The manufacturer may identify suitable zones or restrictions related to the shape and construction. Give the installer the exact bath model and the proposed filler reference before making holes. This is particularly important where a curved rim, narrow ledge or double-ended design limits the available flat surface.
For an existing bath, photograph the tap position and measure the holes before choosing a replacement. Record any reinforcing components or previous repairs visible underneath. If the existing filler moves when operated, investigate the support and fixing condition rather than assuming new washers alone will solve it. The bath edge needs to remain suitable for the replacement hardware and normal operation. Do not use a different filler to conceal cracking or damage without having the bath assessed.
Count holes and measure centres
A two-hole bath filler usually presents one connected body with hot and cold connections beneath it, but check the actual product drawing rather than relying on the general category. Measure from the centre of one mounting hole to the centre of the other. Overall product width is a different dimension and cannot be used as a substitute. Record the hole diameters and the available flat area around them as well as the spacing.
The Nuie Arvan chrome deck-mounted bath filler and Nuie Binsey chrome deck-mounted bath filler are useful products to compare by their technical information. Their listed overall dimensions differ, and that alone does not establish whether either fits existing holes. Look for the connection centres, fixing arrangement and the manufacturer's installation requirements. If these details are unclear, resolve them before purchase rather than expecting the installer to adapt the bath to whichever model arrives.

Check the spout against the inside edge
The spout outlet needs to deliver water into the bath rather than onto a broad rim or a sloping ledge. Measure the distance from the proposed mounting position to the inside edge, then compare it with the product's actual spout projection. Overall depth in a title may include parts behind the outlet or use a different reference point. A dimensioned drawing is more useful than judging the reach from a photograph taken at an angle.
Consider the outlet height and direction of flow together with reach. A spout that clears the rim may still place the stream awkwardly against the side of the bath. The intended bath position, wall finish and nearby fittings can affect the result. Ask the installer to assess the complete geometry before final preparation. Avoid choosing an excessively projecting spout simply to be safe, because it can create an unnecessary obstruction within the bathing area.
Leave room for the controls
Check the full movement of handles or levers, including clearance from the wall, bath screen and any upstand. A filler body may fit the rim while a lever contacts a wall before it reaches its intended position. The user also needs room to grip and operate the control. Compare the plan view and front view of the product rather than checking only the spout's centre line.
The Nuie Cyprus chrome bath filler and Nuie Windon chrome bath filler offer different styling to investigate once the mounting requirements are clear. Do not assume similar-looking lever controls have identical travel or grip. Where someone has limited hand strength or dexterity, discuss their needs with the installer and try a representative control where possible. Appearance should support comfortable use rather than dictate a handle arrangement that is awkward every day.
Understand manual temperature control
A conventional manual bath filler combines the supplies according to the controls; it should not be described as thermostatic unless the exact product has that function. Ceramic disc technology describes a valve mechanism and does not, by itself, provide thermostatic temperature regulation. Check the product's stated control type and discuss any temperature-limiting requirements with the installer as part of the complete system.
Water temperature and behaviour depend on the supply and installation, not just the visible tap. Avoid relying on a particular handle position as a guaranteed bathing temperature. Have the installer commission the arrangement and explain its operation. Where protection against scalding is needed, the appropriate system and installation requirements should be assessed professionally. Do not substitute a claim about smooth controls or a family-friendly appearance for verified temperature-control performance.
Match the filler to the water supply
Check the minimum operating pressure and the manufacturer's flow information for the exact model. A product suitable for one supply arrangement may perform differently on another. The pressure available while water is flowing matters, and the hot and cold supplies should be assessed together. Give the plumber information about the system rather than assuming every bath filler will work equally well because the connection threads appear compatible.
Do not promise a filling time from the tap's appearance or a single catalogue figure. Bath capacity, usable hot-water delivery, pipework and the actual flow at the outlet all influence the result. If filling speed is important, ask the installer to assess the available supply and compare reliable flow data for the shortlisted fillers. Where published figures appear inconsistent, obtain clarification instead of choosing the most generous number or treating minimum pressure as a guarantee of rapid filling.
Plan access beneath the bath
The connections and fixing nuts need enough space for installation and future servicing. Check their position against the bath frame, wall, waste pipe and any structural components. A filler placed centrally along a wall-side rim may look balanced but be difficult to reach once the bath is fitted. Discuss access before the bath is enclosed, rather than leaving the problem until a cartridge or connection needs attention.
Use the bath panel fitting and plumbing-access guide when planning the enclosure around the bath. Access should be practical for the components actually installed, not just a small opening somewhere nearby. Do not permanently seal serviceable connections behind decorative finishes without a suitable maintenance arrangement. Keep the bath, filler and panel specifications together so each trade understands the intended installation.

Replacement work needs an underside survey
Before removing the existing filler, establish how it is connected and whether the pipework and isolation arrangements are suitable for the replacement. Old fittings may be difficult to reach or have limited movement, and rigid pipe positions may not suit a different connection layout. Have a plumber assess the work and identify the required fittings. Do not assume flexible connectors solve every alignment or access problem.
Measure the visible footprint of the old tap as well as the holes. A new base may reveal staining, old sealant or marks on the bath rim. That is a visual issue separate from functional compatibility, but it is worth discovering before the old filler is removed. Inspect the rim for damage and check that the proposed fixing method is appropriate. A neat-looking replacement should also be securely supported and serviceable beneath the surface.
Compare finish after compatibility
Once the mounting and supply requirements are confirmed, choose a finish that works with the room. The Arvan matt black bath filler and Arvan brushed brass bath filler offer alternatives to chrome, with other finish options available across selected ranges. Confirm the exact model and finish reference because similar names from different ranges may not look identical beside each other.
Match the visible waste and nearby fittings where appropriate, but do not select them by colour alone. Their functional compatibility still needs checking. Think about the cleaning routine and follow the manufacturer's finish-care instructions. Avoid assuming a plated or coloured surface can be polished in the same way as another material. A finish that is protected during fitting and cleaned correctly is easier to keep looking consistent across the bathroom.

Prepare the order and installation check
Create a short schedule containing the bath model, filler reference, finish, mounting holes and centres, spout projection, supply requirements and access plan. Record what is included and what must be ordered separately. A bath filler is not automatically supplied with a waste or shower kit. If a shower handset is required, confirm whether a different mixer arrangement is needed rather than adding an unrelated attachment to a filler.
Inspect the delivered item before installation and compare it with the approved reference. Have the plumber follow the manufacturer's instructions, flush the supply as appropriate and test the finished installation for leaks and correct operation. Check the controls and water delivery with the bath in its final position. Keep the instructions and exact model details for replacement parts rather than relying on a photograph of the finished tap.
Frequently asked questions
Does the overall width tell me the tap-hole centres?
No. Overall width and connection centres are different dimensions. Use the drawing for the exact model and measure the existing holes from centre to centre.
Can a deck-mounted filler be fitted anywhere on an undrilled bath?
No. Follow the bath manufacturer's permitted preparation and mounting requirements. Confirm the suitable position, support and access before drilling.
Is a ceramic disc filler thermostatic?
Not necessarily. Ceramic disc refers to the valve mechanism. Thermostatic control is a separate function that must be stated for the exact product or provided through an appropriately specified installation.
Will a larger spout fill the bath faster?
Appearance alone does not establish flow. Compare reliable manufacturer data with the actual supply and pipework, and ask the plumber to assess expected performance.
Can I keep the existing pipework?
Possibly, if its condition, connections and arrangement suit the new filler. Have it inspected before assuming the replacement is a direct swap.
What should I send when asking JJ about a replacement?
Provide the bath model, hole measurements, photographs above and below the rim, supply information and preferred filler reference. Call JJ Building Materials on 01202 113233 to clarify the product options before installation is arranged.